All other service settings of TV set are made in so called service mode of TV set operation. To enter this mode of operation press
the keys in the following sequence: "TV", "I", and "STOP" in the period of 5 seconds from switching on the TV set to normal mode
of operation. When the TV set is switched over to service mode the following status line with service parameter and parameter value appears on the screen:
SERVICE PARAM: XX VALUE: xx
The parameter to be set is selected with keys (P+/P-), and selected parameter is set with keys (volume+ /volume-). Each
time you press the key for parameter selection ( ) the value of preselected parameter is stored. Therefore when the last setting is
performed you must press one of the two keys once again. Values of individual parameters are expressed in hexadecimal form due
to limited capacity of the memory. Values of individual parameters are variable from 0 to 3F, with the exception of parameters 11,
12 and 13 where values are changed from 0 to 7F and O1, O2, O3, O4, which have value range between 0 and FF.
When setting is finished it should obligatory be concluded with "STOP" key. After a few seconds the status line disappears and
service adjustment is accomplished.
Gorenje Chassis E9 TV Service mode
HARDWARE OPTIONS FOR E9 1 PAGE (SDA5255 EV E9 1P 19 99)
P0.6 (PIN 3, SHRINK DIL PROCESOR): SECAM L
JUMPER J902 INSERTED SECAM L IS NOT SUPORTED
WITHOUT J902 SECAM L IS SUPORTED
P1.4 (PIN 19, SHRINK DIL PROCESOR): D/K
JUMPER J906 INSERTED D/K IS NOT SUPORTED
WITHOUT J906 D/K IS SUPORTED
PIP SDA9288X IS AUTOMATICALY RECOGNITED VIA I2C BUS.
MSP 34XX IS AUTOMATICALY RECOGNITED VIA I2C BUS.
STEREO OVER SCART TDA8425 IS AUTOMATICALY RECOGNITED VIA I2C BUS.
ZOOM IS POSSIBLE ONLY WITH 110 DEGREE VIDEO PROCESSORS.
EEPROM SELECTIONS
24C08 ATMEL or MIKROCHIP
SPECIAL RC5 COMMANDS IMPLEMENTED IN E9 SW:
SYSTEM 7 CODE 0 : Switch ON TV. TV force into PSM mode. There is no automatic switch OFF on noise channel - red MENU. (CONTROL)
SYSTEM 7 CODE 1 : Switch ON TV. Picture is coming without 10 sec. delay (for Production purposes)
SYSTEM 7 CODE 2 : Shortcut to SERVICE MODE.
SYSTEM 7 CODE 3 : Clear all programs from EEPROM (for QUELLE) only in PICTURE mode
FATAL ERROR DETECTION
VIDEO PROCESOR NOT DETECTED, or POWER UP RESET of Video Processor not finished – LED flashing with 1Hz.
date: 19.10.1999 Prepared by PIRNAT Iztok
Photo credit : www.reobama.com
OPTION BYTES FOR E9 1 PAGE (SDA5255 EV E9 1P 19 99):
O1 :
7 6 5 4 3 2 1 0
bit 0: 1 - NTSC ENABLE
0 - NTSC DISABLE
bit 1: 1 - BLUE BACK ENABLE
0 - BLUE BACK DISABLE
bit 2: 1 - DYNAMIC SKIN CORRECTION ANGLE 123 degrees
0 - DYNAMIC SKIN CORRECTION ANGLE 118 degrees
bit 3: 1 - DYNAMIC SKIN CONTROL ENABLE
0 - DYNAMIC SKIN CONTROL DISABLE
bit 4: 1 - BLUE STRATCH ENABLE
0 - BLUE STRATCH DISABLE
bit 5: 1 - BLACK STRATCH ENABLE
0 - BLACK STRATCH DISABLE
bit 6: 1 - HOTEL MODE ENABLE
0 - HOTEL MODE DISABLE
bit 7: 1 – AUTO ON ENABLE (for CONTROLA department: after power ON, TV set automatic switch ON, NO change of colour). Sound is
automatic STORED if change the sound level SCHLECKER TV.
0 – AUTO ON DISABLE
O2 :
7 6 5 4 3 2 1 0
bit 0: 1 - PAL I ENABLE
0 - PAL I DISABLE
bit 1: 1 - MULTISTANDARD TV ENABLE (BG, DK(if W/O jumper), I(if option bit PAL I ENABLE)
0 - MULTISTANDARD TV DISABLE ((if PAL I ENABLE only PAL I),(if PAL I DISABLE -> BG and DK if W/O jumper for DK))
bit 2: 1 – HBL (110 degree) bit video proc. / AVL mono version (90 degree) - ENABLE always
0 - HBL (110 degree) bit video proc. / AVL mono version (90 degree) - DISABLE always
bit 3: 1 – ITALIAN CHANNAL ENABLE (C13 – C20)
0 – ITALIAN CHANNAL DISABLE
bit 4: 1 - ZOOM is DISABLE (only 4:3 mode)
0 - ZOOM is ENABLE (only 110 degree)
bit 5: 1 - AUTOMATIC SWITCH ON (BCO = 1)
0 - 8 SEC. DELAYED SWITCH ON
bit 6: 1 – GOLDEN DEVICE ENABLE (stabilisation of horizontal OSD)
0 – GOLDEN DEVICE DISABLE
bit 7: 1 - USER SET 38
0 - USER SET 06
Gorenje Chassis E9 TV Service mode
Entering Gorenje Chassis E9 factory mode to change any value on the factory service mode, please write down all the original factory settings. tvservicemenu are not responsibility for any damage, data error and unwanted effect after using our service code and information on these page.
Original remote or universal remote control needed as a tools to program the factory mode (Recommended use the original remote control).
If the code above do not match to your television please browse another service code in sitemap page.
Universal Remote - Service Mode - TV Factory menu codes
You are reading Gorenje Chassis E9 TV Service Menu. Bookmark the Gorenje Chassis E9 TV Service Menu page to your favorite.
https://tvservicemenu.blogspot.com/2014/12/gorenje-chassis-e9-tv-service-menu.html.
Author : Meilyn, Ricky and Akzai Rajali
Editor : Denny Wowor
Gorenje Chassis E9 TV Service Menu (All TV Service Menu Code)
5
stars -
"Gorenje Chassis E9 TV Service Menu"
by Admin 2
Enter to Gorenje Chassis E9 TV Service Menu mode Written on December 22, 2014