All TV Service Menu Code

Zenith 42LC2DA TV Service menu

  • Home
  • Database
  • LCD
  • LED
  • CRT
  • Plasma
  • DLP
  • FORUM
  • Upload
  • Download
  • Join
  • Rss
  • Mobile
  • Grundig TV Hotel mode
  • Grundig Chassis 22.1 TV Service menu
  • Grundig Chassis D6 TV Service menu
  • Beko, Arcelik, Grundig LCD TV service Menu
  • Sanken TV Service Menu
  • Graetz TV Service Menu
  • Beko L6B TFT TV Service menu
  • Dynex DX-LCD32 TV Service Menu
  • Sharp LCD TV Service Menu
  • Sansui TV Service Menu
Home » LCD » Service mode » Zenith » Zenith 42LC2DA TV Service menu

Zenith 42LC2DA TV Service menu

Zenith 42LC2DA TV Service menu | Author | July 04, 2015
Follow @TSM

Zenith 32/37/42LC2DA 

Application Object
These instructions are applied to all of the Zenith LCD or LG TV using chassis LA63E.
2. Notes
(1) Because this is not a hot chassis, it is not necessary to use an isolation transformer. However, the use of isolation transformer will help protect test equipment.
(2) Adjustments must be done in the correct order.
(3) The adjustments must be performed in the circumstance of 20±5°C of temperature and 65±10% of relative humidity if there is no specific designation.
(4) The input voltage of the receiver be must kept 110V, 60Hz when adjusting.
(5) The receiver must be operational for about 15 minutes prior to the adjustments.
Perform preliminary operation after receiving 100% White Pattern (06CH).
(Or 3. White Pattern status of Ez-Adjust) White Pattern entry method
A) Enter into Ez-Adjust by pressing the ADJ key on the adjustment Remote Control.
B) 100% FULL WHITE PATTERN appears if pressing the OK key after selecting the 3.WHITE
PATTERN with the CH + / - KEY.
* It is possible to heat run the set without a separate signal generator in this mode.
Caution : Care must be taken as afterimage phenomena may occur about the black level part of
screen If leaving pause image turned on for more than 20 minutes (especially inner digital pattern (13
CH), Cross Hatch Pattern (09CH) with significant black/white contrast).


Service menu Zenith 42LC2DA TV

Zenith 42LC2DA TV Service menu

Photo credit : sissyprissyandmom.blogspot.com


If you turn on a still screen more than 20 minutes (Especially Digital pattern(13 CH), Cross Hatch Pattern), an afterimage may occur in the black level part of the screen.

Zenith 42LC2DA Adjustment
(1) Select Component1 as the input with 100% Horizontal Color Bar Pattern(HozTV31Bar) in 480i Mode
(2) After receiving signal for at least 1 second, press the ADJ Key on the Service R/C to enter the ‘Ez - Adjust’ and select the ‘2. ADC 480i Comp1’.
Pressing the Enter Key to adjust automatically.
(3) When the adjustment is over, 'MST3361 Component Success’ is displayed. If the adjustment has errors, 'MST3361 Configuration Error’ is displayed.
(4) Select Component1 as the input with 100% Horizontal Color Bar Pattern(HozTV31Bar) in 1080i Mode.
(5) After receiving signal for at least 1 second, press the ADJ Key on the Service R/C to enter the ‘Ez - Adjust’ and select
the ‘3. ADC 1080i Comp1/RGB’.
Pressing the Enter Key to adjust automatically.
(6) When the adjustment is over, 'MST3361 Component Success’ is displayed. If the adjustment has errors, 'MST3361 Configuration Error’ is displayed.
(7) After the Component MST3361 adjustment is over, convert the RGB-DTV Mode and display Pattern.
When the adjustment is over, 'MST3361 RGB_DTV Success’ is displayed.
(8) Readjust after confirming the case Pattern or adjustment condition where the adjustment errors.
(9) After adjustment is complete, exit the adjustment mode by pressing the ADJ KEY.
6. EDID(The Extended Display Identification Data)/DDC
(Display Data Channel) Download
This is the function that enables “Plug and Play".

Zenith 42LC2DA HDMI EDID Data Input
Required Test Equipment
1) PC, Jig for adjusting DDC. (PC serial to D-sub Connection equipment)
2) S/W for writing DDC(EDID data write & read)
3) D-Sub cable
4) Jig for HDMI Cable connection

Preparation for Adjustments & Setting of Device
1) Set devices as below and turn on the PC and JIG.
2) Open S/W for writing DDC (EDID data write & read).


Download data PDF



Newer Post Older Post

Share
twitter
Facebook
Linkedin
Digg
Pin it

Universal Remote - Service Mode - TV Factory menu codes

Eleex You are reading Zenith 42LC2DA TV Service menu.
Bookmark the Zenith 42LC2DA TV Service menu page to your favorite.
https://tvservicemenu.blogspot.com/2015/07/zenith-42lc2da-tv-service-menu.html.
Author : Meilyn, Ricky and Akzai Rajali
Editor : Denny Wowor


Zenith 42LC2DA TV Service menu (All TV Service Menu Code)
5 stars - "Zenith 42LC2DA TV Service menu" by Admin 2 Zenith 42LC2DA TV Service menu mode, Zenith 42LC2DA TV factory mode code Written on July 04, 2015



Universal Remote

  • Chunghop RM-168GS code List
  • iWave Supersize Universal Remote
  • Automator URC 200 CD Players
  • Asaki Universal Remote for DVD
  • AMAZONE Universal Remote for DVD

CRT Television

  • Zenit TV Service Menu
  • Hisense HSM 515AV TV Service Menu
  • Grundig CUC 7301 TV Service menu
  • SIERA SG1420 TV Service Menu
  • RCA G27684 TV Service Menu


Plasma Television

  • Samsung HCH 551WX TV Service Menu
  • Beko L5C TFT LCD TV Service Menu
  • Beko LCD PLASMA L6E TV Service Menu
  • Beko Plasma TV Service Menu
  • Samsung Plasma TV Service Menu

LED Television

  • How to enter to Sansui TV Service Menu
  • LG 42LB62 LED TV Service Menu
  • Sanyo LED LCD TV Service Menu
  • How to enter to Telefunken TV Service Menu
  • Konka LED TV Service Menu

LCD Television

  • Hisense LCD 19V87 TV Service menu
  • Insignia NS LCD37HD-09 TV Service menu
  • Hisense K15 Series TV Service Menu
  • Hisense MT5380 TV Service menu
  • Grundig 42PX TV Service Menu


  • FORUM
  • Announce
  • Claim
  • Contributor
  • Universal Remote
  • Terms of Service
  • Privacy Policy
  • About
  • Contact
© 2008 - tvservicemenu. All Rights Reserved