Grundig Beko MF 72-2015 TV Service Menu

Grundig Beko MF 72-2015, MFW 82-201 STF 72-2010 TV Service Menu
Chassis 22.2
Arcance 72 Flat MF 72-2015 Top GBC9600
Arcance 82 Flat MFW 82-2015 Dolby GBC9700
STF 72-2010/8 Top GBE0100
Enter to Service Mode: Via " i " –> Service Code "8500"
Call up the Menu: Press button P+ / P– –> button "OK"
Adjustment: Press button / or 1 - 3, 4 - 6
Break of the Menu: Press button " i "
End the Service Mode: Press button "TXT"
1. Basic Settings
The following table shows all type specific basic settings in the service mode. In addition all values marked with * must be adjusted according to adjustment (Service Manual, Part Number
720100483000, page 2-3).
2. Change of the Feature Board
After changing the feature board all settings in the service mode must be done according to the table "Basic Settings" (point 1).

Photo credit to www.wotif.com

3. Autoprogram (ATS)
Buttons " i " (Main menu) –> P+ / P– "SETUP" –> "OK" –> P+ / P–
"Autoprogram" –> "OK" –> P+ / P– / / select Country and start search with "OK".
The autoprogram system stops at every station of acceptable reception quality (AFC and coincidence) and stores the station data and the respective standard automatically. The system then continues searching.
Pressing the " i " button stops the ATS function.
4. Software Version Number
The software version number is shown in the Service Menu:
eg. SBD.128-A08
16:12:25
05/13/04
5. Test Patter
– Activate the service mode: " i " –> "8500"
– Press butten "AV".
6. "Stock Ticker"
Quick horizontal moving text sometimes may be not readable in good quality. Is the option "STOCK TICK." switched to "enable" the text is more clear. Than dependend on the picture content the whole
picture may shake vertically if there is a moving text.
Stock Ticker Option: " i " –> "8500" –> P+ / P– "OPTIONS" –> "OK" –> P+ / P– "STOCK TICKER" –> "OK" –> / "enable" or "disable".
7. Protection Circuit In case of mulfunction the set is switched to standby via line PROT at Pin 124 of IC401/SDA6000. This protection circuit can be switched off in the service mode to find the defect: " i " –> "8500" –>
P + / P– "OPTIONS" –> "OK" –> P+ / P– "PROTECTION" –> "OK" –> / "NO".
After finishing the repair the protection circuit must be switched on again (YES)!
8. EEPROM Edit This function is only for development. Any settings may cause a defectiv
set.
9. Basic values "PRESET"
Attention: All device-specific values will be replaced by basic values when calling up any "PRESET". The unit functions are not ensured after calling up any presets. All settings in the service mode must be done according to the table "Basic Settings" (point 1).
Call up: " i " –> "8500" –> P+ / P– "PRESET" –> "OK".
The following basic values can be loaded:
– Options
– Sound Options
– IF Adj.
– Geometry Adj.
– Video Adj.
– All Options & Adj.

Beko L5C TFT LCD TV Service Menu

Beko L5C TFT- LCD TV Service Menu LC CHASSIS
Service Menu is entered by pressing 9, 3, 0, 1 keys on the remote controller when the Picture icon is
highlighted in the Main Menu.
Service Menu has 3 sub-menus. These are:
• Options
• Adjustments
• Selections.

Navigation through these menus can be done by pressing OK button. Every adjustment made in this
menu is saved automatically.
OPTIONS
Options are adjustments that the user can select On or Off.
• SCART 2
• FAV
• SVHS
• HOTEL MODE
• STAND BY
• MSP CARRIER MUTE
• WSS SCART
• FIRST ATS

Photo credit to www.techfreak.pro

Beko L5C TFT- LCD TV Service Menu SCART 2 / FAV / SVHS
If a source is disabled in the Service Menu, it will be skipped during source switches. If SCART2 is
enabled, SW assumes that the FAV source share the same path as the SVHS source on the HW. If it is
disabled, it is assumed that FAV and SVHS share separate paths. TUNER and SCART1 are enabled by
default.

HOTEL MODE Beko L5C TFT- LCD TV Service Menu
Enabling Hotel Mode has two effects. First, SETUP menu is no longer accessible by the user. Second,
maximum adjustable volume value is limited to HOTEL VOLUME value. This value can be adjusted in the
ADJUSTMENTS sub-menu of the Service Menu.
STAND BY
If this Option is OFF, the TV will stay in Stand By mode after a Power On. If this Option is ON, the TV will
recall its last stand by status before the Power Off, and switch on from Stand By automatically, if the last
state was ‘Stand by On’.
MSP CARRIER MUTE
If this option is ON, sound processor’s carrier mute functionality will be enabled. The MSP will mute the sound automatically if the signal quality is bad. Setting this option Off will disable this functionality.
ATS If this option is set to ON, TV will display Country Selection menu in the next start. After some country is
selected, the user will be prompted for the start of AutoProgramming process.

Beko L5C TFT- LCD TV Service Menu ADJUSTMENTS
This sub-menu contains numeric adjustments. These items are:
• WHITE R
• WHITE G
• WHITE B
• BRIGHTNESS
• CONTRAST
• COLOR
• PRESCALE FM
• PRESCALE NICAM
• PRESCALE SCART
• HOTEL VOLUME
WHITE R / WHITE G / WHITE B
These are used for color bias adjustment. Unlike other items in the service menu, changes will take effect immediately.
PRESCALE FM / PRESCALE NICAM / PRESCALE SCART These are prescale values that will be used for the initialization of the sound processor (MSP), at the next switch on.

Beko L5C TFT- LCD TV Service Menu HOTEL VOLUME
This value is used as the volume limit, when the Hotel Mode is on.
SELECTIONS
This sub-menu contains selections.
• TUNER TYPE SAMSUNG / PHILIPS
• TELETEXT NO TEXT / FAST / FAST&TOP
• MSP CLIP REDUCE VOL / REDUCE TONE
TUNER TYPE
One of two supported tuner can be selected from this item. System must be restarted for this change to take effect.
TELETEXT
NO TEXT: Teletext is totally disabled. TXT/MIX button will not be functional. AUTO picture format mode will be disabled in RF, F-AV and SHVS modes. Naming and sorting functionality during Autoprogramming will be disabled.
FAST: TOPtext functionality will be disabled.
FAST&TOP: TOPtext functionality is enabled.
TIMER MODE
If OFF TIMER is selected, the user will be able to enter time of the day info for the TV to switch off. If SLEEP TIMER is selected, the user can specify some time period, after which the TV will go to stand by automatically.

MSP CLIP
This selection identifies which method will be used by the sound processor to prevent clipping effects on volume.
Beko L5C TFT- LCD TV Service Menu AUTO PROGRAMMING
When the user selects the Autoprogram item in Setup menu, Country Selection menu is opened. The user must select a country before the Autoprogramming starts. Broadcast system will be selected according to the country selected.
Broadcast systems according to countries:
BELGIUM BG + L
CROATIA BG
CZECH REP. DK
DENMARK BG
FINLAND BG
FRANCE L + BG
GERMANY BG
GREECE BG
HUNGARY DK
IRELAND I
ITALY BG
NETHERLANDS BG
NORWAY BG
POLAND DK
PORTUGAL BG
SPAIN BG
SWEDEN BG
SWITZERLAND BG + L
TURKEY BG
UNITED KINGDOM I
For countries France, Belgium and Switzerland, autoprogramming is done twice. For Belgium and
Switzerland, first BG channels will be searched, after the search in BG is done, searching will restart for L
standard. If the selected country is France, the sequence of standards is reversed, thus, first L then BG.
TELETEXT LANGUAGES
L5C SW decides which teletext language group will be used for teletext decoding, according to the
country selected for autoprogramming.Teletext languages according to countries:
EAST EUROPE:CROATIA ,CZECH_REP, POLAND
WEST EUROPE: BELGIUM ,DENMARK, FINLAND, UK, FRANCE, GERMANY,
IRELAND ,ITALY ,NETHERLANDS, NORWAY, PORTUGAL,SPAIN, SWEDEN, SWITZERLAND,
HUNGARY
TURKISH-GREEK:GREECE TURKEY
PC MODE
PC mode can be entered by pressing PC button on the remote controller. User can return back to TV
mode by pressing the PC or TV buttons.
After the switching to PC mode, VGA input will be displayed on screen, as soon as the mode (input
resolution and frequency) is determined.
If there is no input from the VGA input, NO SIGNAL dialog will be displayed for 15 seconds. At the end of this period if there is no signal from VGA input, the TV will go to Sleep State. While in the sleep state, the TV will keep monitoring the VGA input. If VGA signal is detected, the TV will wake from Sleep State, to PC mode. Alternatively, the user may select to switch the TV on from Sleep State, just like switching on from Stand-by. In this case, the set will switch on from TV mode.

Beko LCD PLASMA L6E TV Service Menu

Beko LCD PLASMA L6E – PE CHASSIS
Service Menu mode Beko LCD PLASMA L6E
Service Menu is entered by pressing “9, 3, 0, 1” keys on the remote controller when the OSD
Menu is Picture icon is highlighted in the Main Menu.
Service Menu has 3 sub-menus. These are:
• Adjustment
• Selection
• Option
Navigation through these menus can be done by pressing OK button. Every adjustment made in this menu is saved automatically.

• ADJUSTMENT
FACTORY MODE : There are two(2) values for this adjustment “OFF” and “ON”.
When “OFF” is set, the unit goes to stand-by at start up else the
unit operates directly.
I2S PRESCALE : This topic adjusts the level of the volume received via HDMI.
SCART PRESCALE : This topic adjusts the level of Analog Stereo Sound at MSP Scart Audio inputs.
NICAM PRESCALE : This topic adjusts the level of NICAM Stereo Sound at MSP IF Audio inputs.
FM/AM PRESCALE : This topic adjusts the level of FM/AM Stereo Sound at MSP IF Audio inputs.
AGC : Adjusts the AGC(Automatic Gain Control) value
WHITE R / WHITE G / WHITE B/ PIP WHITE R / PIP WHITE G / PIP WHITE B These are used for color bias adjustment. Unlike other items in the service menu, changes will take effect immediately.

Photo credit to www.wotif.co.nz

• SELECTION
FACTORY RESET : Resets all the values to factory values.
BACKLIGHT : Selects the backlight illumination level of the panel.
TUNER TYPE : Selects the type of the tuner, should be selected parallel to the tuner used in the unit.
TELETEXT : Selects the Teletext type(No Text, Fast, Fast&Top).
TIMER MODE : If OFF TIMER is selected, the user will be able to enter time of the day info for the TV to switch off. If SLEEP TIMER is selected, the user can specify some time period, after which the
TV will go to stand by automatically.
MSP CLIP : There are four(4) values for this topic, with “Reduce Vol” MSP output limiting is done by Volume, with “Reduce Tone” MSP output limiting is done by bass and treble, with “Compromise” MSP output limiting is done by volume, bass and treble, and with “Dynamic” MSP output limiting is done automatically internal by IC.
HOTEL MAX VOLUME : By this topic the volume level at Hotel Mode can be limited, also see HOTEL MODE under OPTIONS.
COUNTRY : Selects the Country.

• OPTIONS
HOTEL MODE : Enabling Hotel Mode has two effects. First, SETUP menu is no longer accessible by the user. Second, maximum adjustable volume value is limited to HOTEL VOLUME value.
STDBY RECALL : If this Option is “OFF”, the TV will stay in Stand By mode when switched on. If this Option is “ON”, the TV will recall its last stand by status RECALL LAST AV : If this Option is “ON”, then the TV will recall the last AV mode when switched on, If this Option is “OFF” then will start up with st-by.
MSP CAR. MUTE : If this option is “ON”, sound processor’s carrier mute functionality will be enabled. The MSP will mute the sound automatically if the signal quality is bad. Setting this option “OFF” will disable this function. WSS RF : If this option is “ON”, TV automatically goes to WSS
mode when recognized via RF. Setting this option “OFF” will disable this function.
AUTO AV 16:9 : If this option is “ON”, TV automatically goes to 16:9 mode when recognized via AVs. Setting this option “OFF” will disable this function.
FIRST ATS : If this option is set to ON, TV will display Country Selection menu in the next start. After some country is selected, the user will be prompted for the start of Auto Programming process.
HEADPHONE : If the LCD consist Headphone this parameter will be opted as “ON” else “OFF”
PARENTAL LOCK : When “ON” set, then “Parental LOCK” is added at OSD.

Beko, Arcelik, Grundig LCD TV service Menu

Beko, Arcelik  and Grundig LCD TV Service mode
To enter service menu, just like in the previously launched products, we press menu button of the remote control and enter 9, 3, 0, 1 in sequence for BEKO / ARÇELİK brand TVs. For GRUNDIG brand we enter 8, 5, 0, 0.
As the chassis improvement and development works go on throughout the production, service menu items may vary according to the software version. The following explanations are service menu settings of the current version.
This menu contains general settings of the system.

TF CHASSIS / TELEVISION for Beko, Arcelik  and Grundig LCD TV Service mode
TV MODE tab contains "Factory" and "Customer" options. It is used to perform factory controls and settings more efficiently and faster. On the TVs delivered to the customer, this setting is absolutely selected as "Customer." Otherwise, it will lead to customer complaints such as "TV automatically turns on after power failures" or "different functions operate from the remote control".
HDCP VERIFY: It must be checked if HDCP key is loaded or not during factory controls. HDCP key stands for ““High Bandwidth Content Protection Key”. This key is used to prevent copying of data on digital sources such as DVD or blue-ray. With HDCP, video data is transmitted from the source to the receiver as encrypted. Therefore, to watch HDCP encrypted DVDs or blue-ray, HDCP key should have been loaded on TV. On the products with HDCP installed, SUCCESS message is included.
DEBUG MODE is a feature, which is used to track software modifications made on TV during R&D stage. This setting must be "Off" on TVs delivered to the customer.
PLUG PLAY (Demo Mode): A navigation key is pressed after having completed all settings and checks in the factory. Later, "Please wait" message appears; and when you see the message "DONE", the device should be unplugged and plugged again. With this process, television will be set to its initial values before delivery. It will be proper to set Plug&Play tab after servicing. After pressing right key on the tab, EEPROMs will be loaded with factory defaults. TV can be shipped to the customer after this setting. Please note that any warning is not displayed or you do not have to exit the menu while Plug&Play is getting activated. You should be careful not to take the device into Plug&Play mode by mistake.
ATS (Automatic Tuning System) tab ensures that the channels are arranged in order after automatic search. However, there is a broadcast support to order the channels. It is active when “On” is selected. “On” should be selected in TF-chassis products.
SRS (Virtual multi-channel sound system) turns on and off SRS Tru-Surround XT HD feature. SRS Tru-Surround XT® creates a sound experience surrounding the user similar to 5+1 sound systems, thanks to multi-channel audio by using two loudspeakers produced by SRS company. SRS is an optional feature that can be selected upon the customer’s request.
BLUE BACK enables us to determine background when there is no picture on the screen. When "On" is selected, background will be blue; and when "Off" is selected background will be black or snowing. “On” should be selected in GRUNDIG brand products and “Off” in other products.
HOTEL tab should be set to "On" on hotel TVs, and it should be set to "Off" in other products. When the hotel model is "On", certain features designed for the hotel use are activated; the user cannot change the channels set by the service, for example, or the volume cannot be increased more than a certain level.
Beko, Arcelik  and Grundig LCD TV Service mode, CI KEY VERIFY indicates if CI Key has been installed or not. This menu cannot be changed. This option should appear as “Pass” in the products with CI Plus feature. CI Key is the keyword on the card which is inserted to decrypt the broadcasting. This menu is a control indicator and changes automatically. This keyword is installed during TV production and it becomes a kind of ID for your TV when watching encrypted channels. TF-chassis products support CI+ feature.
Launched in 2008, it is a new encryption standard developed with the collaboration of consumer electronics and scrambled digital broadcasting companies. So far, it was possible to copy the programmes after decoding process; however, now they cannot be copied thanks to that main IC coming with the CI Plus has a key. In this system, broadcasting is initially decoded on CI card. The broadcasting transmitted to the main IC from the CI card is also encrypted and it is decoded with CI Key, which is a factory setting and different for each TV. Thus, there will be no free encrypted broadcasting on the bare line and encrypted broadcasting cannot be copied. C+ feature is standard in all the products with TF chassis.
The settings under source configuration tab determine which sources will be on and which ones will be off depending on customer demands. In the small size products, HDMI3 and HDMI4 are off in standard (NAVAIL); and the sources of DVD and USB can be adjusted optionally. In large size products, DVD will be off in standard. In the products with LOW feature, USB, HDMI2, HDMI3, HDMI4, AV2, COMPONENT and DVD sources will be selected off.
TV Configuration:
This menu contains configuration settings of TV. We may select amongst the menus that are being used and to be used on TV. These settings differ from the "System Configuration". This menu contains the changes which the user can directly observe.
To enter this menu, you should go to "TV configuration" from the service menu and enter the numbers 2, 3, 5, 6 in sequence.
TUNER menu contains the tuner types that can be used on TV. TF chassis currently works with “Alps” branded tuners.

Beko, Arcelik  and Grundig LCD TV Service mode.
DVBT2 (Next generation digital terrestrial broadcasting modulation) can be selected as ON/OFF depending on the customer preference, in the countries that support DVBT2 digital terrestrial broadcasting. DVBT2 is selected OFF in the products to be used in the country. In our country, TRT makes DVBT2 test broadcasting in Ankara.
OSD Selection menu has "Grundig", "Beko", "Arçelik" and "OEM" selections. For Grundig products, “Grundig” is selected. This selection adds Grundig sign next to the user menu and remote control selection is “TP3”. TV brand should be selected in Beko and Arçelik products. This selection is automatically “YB1187R” in the remote control and several brand-specific menus are also added. For other brands, OEM should be selected. If the product is "Grundig", you can enter service menu by pressing "menu 8 5 0 0" keys. If "Beko", "Arçelik" or "OEM" is selected, you can use "menu and 9 3 0 1" keys.
Note: In the smaller size (19”-22”) products with TF chassis, when Arçelik, Beko or Grundig is selected under OSD selection tab, different remote control options will be displayed compared to large size products.

Beko L6B TFT TV Service menu

Beko L6B TFT TV Service mode
1. Activating the Service Menu
When the menu is on the screen press ‘9’, ‘3’, ’0’, ’1’ on the remote controller. This will
activate the service menu.
2. Service Menu Structure
The service menu has three items: display, calibre and version
2.1 Display
Display item has seven options:
a- Panel
Panel option gives information about the current panel resolution. It is a read only
option and can not be set.
b- Power on time
Power on time gives information about the last update time of the SW running. It
is a read only option and can not be set.
c- Backlight on time
Backlight on time option reserved.
d- Scart prescale
Scart prescale option sets the prescale values for the input sounds entering the scart
input of the MSP(Micronas Sound Processor). Changing this value you can adjust
the level of the output sound going to loudspeakers for all the sources except the
Tuners. The range is between 0 and 100.
e- nicam prescale
Nicam prescale option sets the prescale values for the Nicam standard sounds for
tuner inputs. Changing this value you can adjust the level of the output sound
going to loudspeakers for Nicam sounds entering the analog sound input of MSP.
The range is between 0 and 100.
f- fm/am prescale
fm/am prescale option sets the prescale values for the FM/AM standard sounds for
tuner inputs. Changing this value you can adjust the level of the output sound
going to loudspeakers for FM/AM sounds entering the analog sound input of MSP.
The range is between 0 and 100.
g- Agc(Automatic Gain Control) adjust
Agc adjust option sets the input voltage going to IF decoder AGC pin. Changing
this value you can adjust this voltage for optimum Tuner performance. The range
is between 0 and 31.
h- R/G/B Brightness/Contrast: These are used for color bias adjustment. The range is
Between 0 and 255

Photo credit to www.voanews.com

2.2 Calibre Beko L6B TFT TV Service mode
Calibre item has nine options:
a- video format
Video format option force the video format to the desired format. Selectable
formats are Auto, Pal, NTSC and SECAM.
b- colorspace
Colorspace option gives the information about the video input colorspace input to
PW181 IC. Do not change this value unless an error occurred in the colors
displayed.
c- test pattern
This option activates the internal pattern of PW181 IC. There are 3 choices: none, vert bars, solid color. None will deactivate the internal pattern. Vert bars choice activates the bar pattern for the selected color component. Solid color activates the solid pattern with one color selected in color component and also you can change the level of the color by solid field level.
d- Color components:
This option selects the color for the internal pattern of PW181 IC. There are 4 choices: all, red, green and blue. If you choose all, you can see the white pattern and if you choose one of the other choices you can see the test pattern with the selected color.

e- solid field level Beko L6B TFT TV Service mode
This option will adjust the level of the colors for the test pattern. The range is betwwen 1 and 64.
f- Initial ATS This option will enable or disable the Initial setup for the TV. Setting this option to On, the TV will open from the Quick setup menu. Setting this option to Off will disable this option.
g- factory reset Factory reset option executes a reset operation for the NVRAM. Pressing OK
when this option is selected will erase the NVRAM and load default values to NVRAM.
h- dpms This option selects the Power option for the TV. Setting this option to On the TV will switch to the last state for power on transition. Setting this to Off will disable this option and the TV will always switch to Stand-by state while power on transition.
i- osd timeout
This option sets the OSD timeout for the main menu structure. Selections are 5, 15 and 60 secs. The default is 60 sec.
2.3 Version
This item gives the information about the version of the software. Also you can see the
last modified time for the GUI(graphical user interface).

Beko L6B TFT TV Service mode Display menu
ITEM TYPICAL VALUES/OPTIONS
panel 1280x768
power on time 03:39:45
back light time 03:39:45
scart prescale 25
nicam prescale 45
fm/am prescale 24
agc adjust 16
red brightness 128
red contrast 128
green brightness 128
green contrast 128
blue brightness 128
blue contrast 128
calibre menu
ITEM TYPICAL VALUES/OPTIONS
video format auto
color space RGB
test pattern none
color components all
solid field level 33
initial ats on
factory reset press <ok> to reset
dpms on
osd time out 60 sec
version
ITEM TYPICAL VALUES/OPTIONS
Software
SL630T_CH1_T13 L6B 1.22 Chi30
GUI

Beko Plasma TV Service Menu

Enter to Beko 42 Plasma TV Service Menu Mode
PA Chassis Version 1.0
Entering the service menu with user remote control;
Enter  key “1972” when main menu appears on the screen.
Use channel button to navigate and use volume button to change the value settings.

Beko 42 Plasma TV Service Menu
Brightness
Mode
Auto To adjust the general brightness
RS232 Setting 19200 Slip speed for software downloads
Customer Logo X To choose the customer logo, if available (1, 2, etc.)
Operation Time - Shows the operation time since first switch on, can be resetted by
technician
Default Color
Settings
- To adjust the general color settings, normal value is: RGB offset 7
and RGB gain 128
Power On Input Last Defines which input is active after switching on the unit
Temperature
Setting
- Shows temperature threshold for temperature alert function:
Temp1: 60°C; Temp2: 65°C; Temp3: 63°C
also shows all time Max and Min temperature, which can be
resetted by technician
Full Mask off Available functions: inverted, red, green, blue, full white. Might
help against Burn In
Sub Volume - Defines volume setting of each single input separately
Version /
System Info
- Soft-/Hardware version
Reset
Everything
Resets all settings to factory defaults, also erases all channel
settings

Photo credit to www.tripadvisor.com

General Guidance Beko 42 Plasma TV
An lsolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks.
It will also protect the receiver and it's components from being damaged by accidental shorts of the circuitary that may be inadvertently introduced during the service operation.
If any fuse (or Fusible Resistor) in this monitor is blown, replace it with the specified.
When replacing a high wattage resistor (Oxide Metal Film Resistor, over 1W), keep the resistor 10mm away from PCB.
Keep wires away from high voltage or high temperature parts

Before you entering Beko 42 plasma TV factory mode to change any value on the factory service mode, please write down all the original factory settings. tvservicemenu are not responsibility for any damage, data error and unwanted effect after using our service code and information on these page.
Original remote or universal remote control needed as a tools to program the factory mode (Recommended use the original remote control).
If the code above do not match to your television please browse another service code in sitemap page.

.

Beko LCD TV Service menu

Beko LCD TV Service menu mode
Turn on the television
In TV mode press menu button and press the number 9301
In factory mode press TV/TX button
SW prompted when exiting from service mode
To navigate use channel up or channel down
To change the value press volume button
To select submenu page press red,green or blue button of factory service mode.

Photo credit to www.thesundaytimes.co.uk

Beko TV Service Menu

Beko LCD Factory Mode
Beko TV LCD Service Menu mode
Before you entering Beko LCD monitor factory / service mode to change any value on the factory service mode, please write down all the original factory settings. tvservicemenu are not responsibility for any damage, data error and unwanted effect after using our service code and information on these page.

Entering to Beko LCD (Liquid Crystal Display) Factory Mode
Press "i" key Open dialog center.
Press "OK" key Open factory mode.
Press "Pro + | Pro - key to Select the Parameter
Press cursor  "< | >" key to Change the value
Press "TXT" button to Save and exit

Photo credit : gaiamtv.com

Beko 22.1 TV Service Menu

Beko 22.1 TV Service mode
Before you entering Beko 22.1  factory mode to change any value on the factory service mode, please write down all the original factory settings. tvservicemenu are not responsibility for any damage, data error and unwanted effect after using our service code and information on these page.
Original remote or universal remote control needed as a tools to program the factory mode (Recommended use the original remote control).
If the code below do not match to your television please browse another service code in sitemap page.

Beko 22.1 TV Service mode
Press menu and enter key 9, 3, 0 1
Factory mode will trigger and displaying on the screen
Select parameter press program up or program down, change value setings press volume up to increse and volume down to decrese value.
Save and exit press power button on remote control.

Photo by blogs.finnishpod101.com

Service Menu Beko CTV

Service Menu Beko CTV
Service Mode Simultaneous press chanel + & P- on local tv panel and
then power on with main switch.