JVC LM-17G /U Monitor Setting Menu

The Monitor Setting Menu use to JVC LM-17G /E and  JVC LM-17G /C

There are three control buttons located at the lower part of the front panel of your monitor:
MENU/ENTER: Display and select a menu. You can also exit a menu by pressing this button repeatedly.
UP( ): Move upward through the choice in the submenu. If an adjustment bar is displayed, this button increases the setting value.
Down( ) : Move downward through the choice in the submenu. If an adjustment bar is displayed, this button
decreases the setting value.
Menu Operation
1. Press the ‘MENU/ENTER’ button to display the “BACK LIGHT” menu..
2. Press the ‘MENU/ENTER’ button repeatedly to display the menu you want to use.
PICTURE ADJ.
Next page
PICTURE
PHASE
CHROMA
ASPECT
COLOR TEMP.
LOW LIGHT ADJ.
3. Press the ‘UP’ and ‘DOWN’ button to choose the item, and then press the ‘MENU/ENTER’ button to display the
sub-menu.
ASPECT
4 3
16 9
If the item do not have sub-menu, go to the step 4.
4. Press ‘UP’ and ‘DOWN’ button to adjust it, or choose a setting.
5. Press the ‘MENU/ENTER’ button repeatedly to exit the menu.
To return to the menu from the sub-menu, press the ‘MENU/ENTER’ button
The menu will disappear if no operation is performed for approximately 15 seconds.

JVC LT-32A60BU TV Service Menu

Photo credit : reezi.com

In the VIDEO A or B mode (composite video input):
Menu Items
BACK LIGHT You can adjust the light output of the backlight.
PICTURE ADJ. PICTURE, PHASE, CHROMA, ASPECT, COLOR TEMP., LOW LIGHT ADJ. .
SYSTEM SETTING SIGNAL LEVEL, DISPLAY, OSD POSITION, COLOR SYSTEM, AGC, REMOTE,
All reset
In the PC mode (analog RGB input):
Menu Items
BACK LIGHT You can adjust the light output of the backlight.
CONTRAST You can adjust the contrast of the picture.
POSITION ADJ. H.POSITION, V. POSITION
WHITE BALANCE
ADJ.
COLOR TEMP., LOW LIGHT ADJ.
DISPLAY ADJ. AUTO SET UP, CLOCK, PHASE
SYSTEM SETTING DISPLAY, OSD POSITION, REMOTE, All reset
BACK LIGHT menu
You can adjust the light output of the backlight.
PICTURE ADJ. menu
PICTURE ADJ.
Next page
PICTURE
PHASE
CHROMA
ASPECT
COLOR TEMP.
LOW LIGHT ADJ.
PICTURE: You can adjust the levels of black and white on the screen, giving you a darker or brighter picture
overall.
PHASE: You can adjust the picture hue. When the COLOR SYSTEM is BW60, BW50 or PAL, you cannot adjust the PHASE.
CHOROMA: You can adjust the picture color density. When the COLOR SYSTEM is BW60 or BW50, you cannot adjust the CHOROMA.
ASPECT: You can choose the screen aspect ratio between “4 3 ” and “ 16 9 ”.
COLOR TEMP.: If you select ‘COLOR TEMP.’ and press the ‘MENU/ENTER’ button, the “COLOR TEMP.” menu will appear. For details, see the following “COLOR TEMP.” menu.
LOW LIGHT ADJ.: At the video mode: You can adjust the brightness of the dark part of picture.
At the PC mode: You can adjust the R.G.B. balance of the dark part of picture. For details of the adjustments, see “HIGH LIGHT ADJ.” in page10
Next page: If you select ‘Next page’ and press the ‘MENU/ENTER’ button, the next menu will appear.
COLOR TEMP. menu
1. Press the ‘UP’ and ‘DOWN’ button to choose the “COLOR TEMP.”, and then press the ‘MENU/ENTER’ button
to display the sub-menu.
COLOR TEMP.
HIGH
NATURAL
LOW
USER
2. Press ‘UP’ and ‘DOWN’ button to choose one of four Color temp settings: HIGH, NATURAL, LOW and USER.
“USER” setting:
You can store the adjustments of “HIGH LIGHT ADJ.” to the “USER” setting.
In “HIGH”, “NATURAL” and “LOW”, you cannot use “HIGH LIGHT ADJ.”.
1. Press the ‘UP’ or ‘DOWN’ button to choose the “USER” , and then press the ‘MENU/ENTER’ button to return to the “HIGH LIGHT ADJ.” menu.
HIGH LIGHT ADJ.
Next page
RED
GREEN
BLUE
2. Press ‘UP’ and ‘DOWN’ button to choose “RED”, and then press ‘MENU/ENTER’ button to display the adjusting menu.
3. Press ‘UP’ or ‘DOWN’ button to adjust the level, and then press ‘MENU/ENTER’ button to return to the sub-menu
4. Repeat step 3 and 4 for other colors “GREEN” and “BLUE” to complete the “HIGH LIGHT ADJ.” setting.
SYSTEM SETTING menu
SYSTEM SETTING
Exit
SIGNAL LEVEL
DISPLAY
OSD POSITION
COLOR SYSTEM
AGC
REMOTE
All reset
SIGNAL LEVEL: You can choose the signal level from ”STD.” or “AMP.”.
STD.: Select this for normal operation.
AMP.: Select this to watch dark part of the picture better.
DISPLAY: If you select ‘DISPLAY’ and press the ‘MENU/ENTER’ button, you can confirm the current status;
resolution, Horizontal frequency and Vertical frequency.
COLOR SYSTEM: You can choose the color system from NTSC, PAL, BW60 or BW50. Choose the correct color
system when the color is abnormal or no color appears.
AGC: You can turn the AGC (Auto Gain Control) function on (ON) or off (OFF).If you select off(OFF), you can adjust contrast bar.
REMOTE: If you select ON, you can only do remote control. If you select OFF, you can control only by using the monitor’s buttons.
Exit: If you select “Exit” and press the ‘MENU/ENTER’ button, the menu will disappear.
All reset: If you select “All reset” and press the ‘MENU/ENTER’ button, the settings will be return to the factory settings.
 “COLOR SYSTEM” and the input select will not be return to the factory settings.
OSD POSITION:
You can adjust the position of the menu on the screen as following procedure.
1. Select “OSD POSITION” and press the ‘MENU/ENTER’ button, the sub-menu will appear.
OSD POSITION
Next page
H. POSITION
V. POSITION
2. Press ‘UP’ and ‘DOWN’ button to choose “H. POSITION” (horizontal position) or “V. POSITION” (vertical position), and then press ‘MENU/ENTER’ button to display the adjusting menu
3. Press ‘UP’ and ‘DOWN’ button to adjust the position of the menu on the screen.
4. Press ‘MENU/ENTER’ button to return to the “OSD POSITION” menu.
Next page: If you select ‘Next page’ and press the ‘MENU/ENTER’ button, the next menu will appear.
CONTRAST menu
You can adjust the contrast of the image from the PC.
POSITION ADJ. menu
You can adjust the position of the image from the PC on the screen.
POSITION ADJ.
Next page
H. POSITION
V. POSITION
1. Press ‘UP’ and ‘DOWN’ button to choose “H. POSITION” (horizontal position) or “V. POSITION” (vertical position), and then press ‘MENU/ENTER’ button to display the adjusting menu
2. Press ‘UP’ and ‘DOWN’ button to adjust the position of the picture on the screen.
3. Press ‘MENU/ENTER’ button to return to the “POSITION ADJ.” menu.
Next page: If you select ‘Next page’ and press the ‘MENU/ENTER’ button, the next menu will appear.
DISPLAY ADJ. menu
You can do the necessary adjustments to display the image from the PC.
DISPLAY ADJ.
Next page
AUTO SET UP
CLOCK
PHASE
AUTO SET UP:
We recommend you to do the AUTO SET UP first. And then adjust the CLOCK or PHASE if necessary.
To use the AUTO SET UP, select this item and press ‘MENU/ENTER’ button. And follow the step 2 of the description
“AUTO SET UP” on page13 .
CLOCK: You can adjust the Clock.
PHASE: You can adjust the Phase.
Next page: If you select ‘Next page’ and press the ‘MENU/ENTER’ button, the next menu will appear.

JVC LM-15G /U Monitor Settings

Thise settings can use for JVC LM-15G /E and JVC LM-15G /C

POSITION ADJ. menu
You can adjust the position of the image from the PC on the screen.
1. Press ‘UP’ and ‘DOWN’ button to choose “H. POSITION” (horizontal position) or “V. POSITION” (vertical position), and then press ‘MENU/ENTER’ button to display the adjusting menu
2. Press ‘UP’ and ‘DOWN’ button to adjust the position of the picture on the screen.
3. Press ‘MENU/ENTER’ button to return to the “POSITION ADJ.” menu.
Next page: If you select ‘Next page’ and press the ‘MENU/ENTER’ button, the next menu will appear.
DISPLAY ADJ. menu You can do the necessary adjustments to display the image from the PC.
DISPLAY ADJ.
Next page
AUTO SET UP
CLOCK
PHASE
AUTO SET UP:
We recommend you to do the AUTO SET UP first. And then adjust the CLOCK or PHASE if necessary.
To use the AUTO SET UP, select this item and press ‘MENU/ENTER’ button. And follow the step 2 of the description “AUTO SET UP” .
CLOCK: You can adjust the Clock.
PHASE: You can adjust the Phase.
Next page: If you select ‘Next page’ and press the ‘MENU/ENTER’ button, the next menu will appear.

PRECAUTIONS
(1) Depending on the around temperature, the brightness leaning occurs. Be careful of the environment in the product installation place and so on sufficiently.
(2) Don't hinder radiation from the back, the heaven and the side. Please refer to the next page that explains about the condition of the installation.
The inside becomes hot if hindering radiation and there is fear, which the inner circuit damages.
(3) Install in the place with good ventilation. Use in the condition that around temperature is in the 0~35°C range.
(4) Avoid preservation and use at the high temperature or high humidity place. If you behave like this, leaning sometimes happens in the screen when the set actives.
(5) Depending on the condition and the environment of display, the slight fleck of the light and leaning of the screen and so on is sometimes conspicuous. This is the characteristic which is peculiar to liquid crystal display. It is not set trouble.
(6) This monitor has cool cathode pipe as the backlight. The time change and the use time sometimes change brightness and condition of display.

JVC LM-15G /U Monitor Settings

Photo credit : uujcu.com

THE ATTENTION IN TRANSPORTATION
When transporting a set, if the load handling is bad (throwing, falling and so on) however it is using a solid box, pressure inside liquid crystal display.
In the case there is fear to break the liquid crystal display while transporting. To prevent from the accident or trouble while transporting, pay attention to choice of the transportation company sufficiently and also arrange for it in the delivery after the attention of the load handling is explained to the transportation company.
This set is used glass for composing liquid crystal display. When carrying, pay attention not to add over vibration and impact sufficiently.

LG Flatron Monitor Service menu

LG Flatron L1800PM LB886F-SL CHASSIS CL-29 FACTORY MODEL: LB886F
The service menu can use to enter Dell 1800FP Monitor service menu mode

All adjustment are thoroughly checked and corrected when the monitor leaves the factory, but sometimes several minor adjustment may be required.
Adjustment should be following procedure and after warming up for a minimum of 10 minutes.
• Alignment appliances and tools.
- IBM compatible PC
- Programmable Signal Generator.
(eg. VG-819 made by Astrodesign Co.)
- E(E)PROM with each mode data saved.

Photo credit to activerain.trulia.com

1. Adjustment Start LG Flatron L1800PM LB886F
1) Display any pattern at any Mode.
2) Run alignment program for LB886F on the IBM compatible PC.
3) Select EEPROM → ALL INIT command and Enter
4) This will make all data to default state
5) Select COMMAND → PRESET START command and Enter

2. Adjustment for Factory Preset Mode LG Flatron L1800PM LB886F
1) Select DIST. ADJ → FOS DEFAULT command and Enter
2) It will copy all factory default data to EEPROM automatically.

3. Adjustment for White Balance LG Flatron L1800PM LB886F
1) Display color 0,0 pattern at Mode 15.
2) Set External Bright to MAX position and Contrast to MAX Position.
3) Select PRESET START → BIAS CAL command and Enter.
4) No attempt to manually adjust, BIAS data is automatically adjusted and saved to the EEPROM.
5) Display color 15,0 pattern at Mode 15.
6) Select DRIVE CAL command and Enter.
7) 5800K and 9300K are automatically adjusted and saved to the EEPROM.
8) Select PRESET EXIT command and Enter.

4. Adjustment for EDID LG Flatron L1800PM LB886F
1) Use this procedure only when there is some probelm on EDID data.
2) Connect the D-sub cable.
3) Select EEPROM → EDID Write command and Enter.
4) Select DDC(A) Write command and Enter.
5) Connect the DVI-I cable.
6) Select DDC(D) Write command and Enter.

Samsung LCD 732N Monitor Service Menu

Samsung LCD 732N Monitor Service mode
LCD-Monitor Chassis LS17PEA &  LS19PEB Model 732N & 932B
Service Function Spec.
How to Display Service mode ?
The value for brightness and contrast should
Within 5 seconds, press the (Enter/Source)
Service function OSD will be displayed.
The service function OSD is based on a grid of 29 columns x 12 rows.
The service function OSD consists of panel information, software version and MICOM checksum.
How to Control Service Function OSD
After changing the panel or lamp, you must reset service function OSD.
The case of panel change
After changing the panel, press the menu key within 5 seconds,.
Then, panel Ch. No increases one step and the panel time information is reset to zero.
Simultaneously, other information is reset to zero (Upper/Lower lamp, Panel cycle).

Samsung LCD 732N Monitor Service mode
1-2-1 General Servicing
Precautions
1. Always unplug the unit’s AC power cord from the AC power source and disconnect the DC Power Jack before attempting to:
(a) remove or reinstall any component or assembly, (b) disconnect PCB plugs or connectors, (c) connect a test component in parallel with an electrolytic capacitor.
2. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position.
3. After servicing, always check that the screws, components and wiring have been correctly reinstalled.
Make sure that the area around the serviced part has not been damaged.

4. Check the insulation between the blades of the AC plug and accessible conductive parts (examples: metal panels, input terminals and earphone jacks).
5. Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON.
Connect an insulation resistance meter (500 V) to the blades of the AC plug.
The insulation resistance between each blade of the AC plug and accessible conductive parts (see above) should be greater than 1 megohm.
6. Always connect a test instrument’s ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrument’s ground lead last.

Some semiconductor (solid state) devices can be easily damaged by static electricity. Such components are commonly called
Electrostatically Sensitive Devices (ESD). Examples of typical ESD are integrated circuits and some field-effect transistors. The
following techniques will reduce the incidence of component damage caused by static electricity.

Photo by benq.co.ae

1. Immediately before handling any semiconductor components or assemblies, drain the electrostatic charge
from your body by touching a known earth ground.
Alternatively, wear a discharging wrist-strap device. To avoid a shock hazard, be sure to remove the wrist strap before applying power to the monitor.
2. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent accumulation of an electrostatic charge.
3. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ESDs.
4. Use only a grounded-tip soldering iron to solder or desolder ESDs.
5. Use only an anti-static solder removal device. Some solder removal devices not classified as “anti-static” can generate electrical charges sufficient to damage ESDs.

6. Do not remove a replacement ESD from its protective package until you are ready to install it. Most
replacement ESDs are packaged with leads that are electrically shorted together by conductive foam,
aluminum foil or other conductive materials.

7. Immediately before removing the protective material from the leads of a replacement ESD, touch the
protective material to the chassis or circuit assembly into which the device will be installed.
Caution: Be sure no power is applied to the chassis or circuit and observe all other safety precautions.
8. Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes
together, or lifting your foot from a carpeted floor can generate enough static electricity to damage an ESD.

LG LCD Monitor Service Menu

LG LCD Monitor Service Menu / Factory Mode
Before you entering LG LCD monitor factory mode to change any value on the factory service mode, please write down all the original factory settings. tvservicemenu are not responsibility for any damage, data error and unwanted effect after using our service code and information on these page.

Photo by www.aquaresorts.com

LG LCD Computer Monitor in turn off mode (Switch Off), press and hold the "MENU" button, then press power button switch to turn on the LG LCD monitor, and then release the MENU button after the LG LCD monitor is turn on.
Press "MENU" button to open the OSD menu, you will see a new option to enter to the factory / service mode, you will see such product model information, creation date, version of the chipset, etc.

Computer Monitor Service Menu

Computer Monitor Service Menu/mode.
Before you entering computer monitor factory mode to change any value on the factory service mode, please write down all the original factory settings. tvservicemenu are not responsibility for any damage, data error and unwanted effect after using our service code and information on these page.

Picture by www.gopixpic.com

BENQ Computer Monitor Service Menu/mode.
BenQ LCD Monitor Service Menu Instructions
Press power button to turn off the computer monitor
Press "MENU" , "EXIT" button and hold the bot button, then press "POWER" button on the lcd monitor to turen on the monitor press "i" button to enter to factory mode.
or second metod is ;
Press power button to turn off the computer monitor
Press the "POWER", "SELECT" and "MENU" button at the same time
If the monitor is ON, press the "V" button to login to factory service mode.
Use cursor up and down to select.
Use cursor right and left to change the value .

Samsung LCD Monitor service menu

Samsung LCD Monitor (Computer monitor) Factory Mode
Before you entering Samsung LCD monitor factory / service mode to change any value on the factory service mode, please write down all the original factory settings. tvservicemenu are not responsibility for any damage, data error and unwanted effect after using our service code and information on these page.

Entering Samsung LCD Monitor
Press the power button and open the OSD menu, Set the Brightness and Contrast to 0 .
Then press the "SOURCE or ENTER" button for 5 seconds until you see a "SERVICE FUNCTION MENU" appears on the screen.

Photo credit : flickriver.com

Philips LCD Monitor Service Menu

Service Menu / Factory Mode PHILIPS LCD Monitor
Before you entering Philips LCD (Lliquid Crystal Display) computer monitor factory mode to change any value on the factory service mode, please write down all the original factory settings. tvservicemenu are not responsibility for any damage, data error and unwanted effect after using our service code and information on these page.

Photo by www.yelp.com

PHILIPS LCD Monitor in switch off mode , Press and hold the "AUTO" and "MENU" button, then press the "POWER" button to turn on the LCD monitor.
Press the "MENU" button to open and display the OSD menu on the screen, at the bottom of the menu, you get additional options.Go and select it then you can log in to the factory / service mode.
Use cursor up and down to select.
Use cursor right and left to change the value .