Turn off the power to put the unit into the STAND-BY mode.
In order to enter the Service Mode, Press "Mute" "1" "8" "2" "POWER" button on the Remote Control.
In case entry into SERVICE MODE is unsuccessful, repeat the procedures above.
Initial DISPLAY State in times of Service Mode Switch overs;
DDP1011(L6)
DNIe
ADV7401(M)
ADV7401(S)
uPD64083
MSP4440
CCA(ON)
Cinema CCA
SP Actuator
ESP
CHECKSUM 0000
OPTION
SERVICE
T_HUR2AUS0_XXXX
200X_XX_XX
T-HURUCOM5-XXXX
T-HUR2AUS1_XXXX
Use channel button to select parameter
Use volume button to change the value settings
Akai DLP PT50DL14X TV Service Menu
Photo credit : inisdesign.com
1. DDP1011
Akai DLP PT50DL14X TV Service mode
1 V-Position 0-60 36 Screen upper and lower adjustment
2 H-Position 0~120 60 Screen left and right adjustments
3 LAMP SYNC Pulse(P) Pulse(P), Pass (T)
4 INDEX DELAY 0~359 40
Synchronizes the base position of the color wheel with the
corresponding color signal.
This is critical to the natural color display. If the index delay
is not properly set, even the correct CCA cordinates will not
help when displaying natural colors.
5 SEQ SELECT 0~15 5 Sequence Selection
6 V-FLIP Normal/Flip Normal Vertica Flip Operation
7 H-FLIP Normal/Flip Normal Horizontal Flip Operation
8 GAMMA 0 ~ 15 2 Gamma Table Selection
9 SLR OFF/ON OFF SLR Funcion On/Off
10 DMD_BIAS B,C,D,E E DMD Bias pin voltage selection
11 Lamp Boost 0~63 13 Lamp Boost value selection
12 Lamp Sync Delay 0~4095 0 Lamp Sync delay value selection
13 Engine Select SAMSUNG SAMSUNG and ZEISS Selection
14 Lamp Watt 120W 120W/132W Selection
15 Lamp Select Osram Philips/Osram/Ushio
16 Test Pattern 0
This displays the built-in pattern of the DDP1011 chip.
DDP1011 drives the DMD panel, so displaying this pattern
means there is no error in the DDP1011 projection function
and the panel itself.
2. DNIe
Akai DLP PT50DL14X TV Service mode
1 Test Pattern 0 Test Pattern Selection
2 NR_MAX Y/C 0~255 48 Temporal NR Gain
3 NR_MIN Y/C 0~255 16 Temporal NR Gain
4 Core 0~15 4 NEOnDCE User Set Up
5 B_RATIO 12000 Low level information for the minimum value
6 BLACK_TILT 0~255 120 Black Stretch Area
7 W_RATIO 12000 High level information for the minimum value
8 WHITE_TILT 0~255 200 White Stretch Area
9 GAIN1X 0~63 30 Gain of horizontal high frequency region
10 GAIN1Y 0~63 20 Gain of vertical high frequency region
11 GAIN2X 0~63 17 Gain of horizontal middle frequency region
12 GAIN2Y 0~63 13 Gain of vertical middle frequency region
13 GAIN3X 0~63 11 Gain of horizontal low frequency region
14 NDON ON ON,OFF Background Noise Detection ON/OFF Switch
15 CORING_ON ON ON,OFFCoring On/Off
16 SCALE_R 0~255 160 Log Mapping Gain
17 WTE_CSC YCCRGB YCCRGB,YPPRGB
18 DITHER_MOD 0 1,2,3
19 RED_C_COEFF 128 Gain adjustment of the contrast for the Red signal
20 GRN_C_COEFF 128 Gain adjustment of the contrast for the Green signal
21 BLU_C_COEFF 128 Gain adjustment of the contrast for the Blue signal
22 RED_B_COEFF 128 Gain adjustment of the brightness for the Red signal
23 GRN_B_COEFF 128 Gain adjustment of the brightness for the Green signal
24 BLU_B_COEFF 128 Gain adjustment of the brightness for the Blue signal
25 Sub Contrast 0~150 120 Brightness adjustment for the high-light parts of the screen
26 Sub Brightness 230 Brightness adjustment for the low-light parts of the screen
27 ALPMAU/L 0~255 50
3. ADV7401(M)
Akai DLP PT50DL14X TV Service mode
1 AUTO COLOR Auto Color function execution
2 SOG_SYNC_LEV Embedded Sync Trigger Level
3 AGC_TIM AGC Time Constant Selection
4 GAIN_MAN ON,OFF Manual Gain Control Enable
5 A_GAIN Manual Gain Value for Channel A
6 B_GAIN Manual Gain Value for Channel B
7 C_GAIN Manual Gain Value for Channel C
8 A_OFFSET Channel A Offset
9 B_OFFSET Channel B Offset
10 C_OFFSET Channel C Offset
11 YPM 0~7 4 Y Peaking Filter Mode
12 YSFM 0~32 1 Y Shaping Filter Mode
13 WYSFM 0~32 19 Wide Band TY Shaping Filter Mode
14 CSFM 0 C Shaping Filter Mode
15 Contrast 0~255 128 Contrast Adjust
16 Brightness 0~255 128 Brightness Adjust
17 Hue 0~255 128 Hue Adjust
18 CKILLTHR 0~7 3 Colour Kill Threshold
19 SD_OFF_Cb 0~255 128 SD Offset Cb Channel
20 SD_OFF_Cr 0~255 128 SD Offset Cr Channel
21 SD_SAT_Cb 0~255 128 Saturation Cb Channel
22 SD_SAT_Cr 0~255 128 Saturation Cr Channel
23 IFFILTSEL 0~7 3 IF Filter Select
24 LTA 0~3 0 Luma Timing Adjust
25 CTA 0~7 2 Chroma Timing Adjust
26 DNR_TH1 0~255 0 DNR Noise Threshold
27 DCT 0~3 0 Digital Clamp Timing
28 LAGC 0~7 0 Luma Automatic Gain Control
29 LAGT 0~3 3 Luma Automatic Gain Timing
30 LMG 1144 Luma Manual Gain
31 CAGC 0~7 5 Chroma Automatic Gain Control
32 CAGT 0~3 3 Chroma Automatic Gain Timing
33 CMG 2458 Chroma Manual Gain
34 CTI_AB_EN ON ON,OFF Chroma Transient Improvement Alpha Blend
Enable
35 CTI_AB 0~3 3 Chroma Transient Improvement Alpha Blend
Alignment & Adjustment
3-6
Akai DLP PT50DL14X TV Service mode
36 CTI_C_TH 0~255 8 CTI Chroma Threshold
37 NSFSEL 0~3 0 Split Filter Selection NTSC
38 CTAPSN 0~3 2 Chroma Comb Taps NTSC
39 CCMN 0~7 0 Chroma Comb mode NTSC
40 YCMN 0~7 0
41 HSSLICE
42 VSSLICE
43 DLL_PH
44 ST_NOISE OxFFFF
45 ALIAS_FILTER_EN
46 DNR_TH2 4
4. ADV7401(S)
Akai DLP PT50DL14X TV Service mode
1 AUTO COLOR Auto Color function execution
2 SOG_SYNC_LEV 0~31 11 Embedded Sync Trigger Level
3 AGC_TIM 0~7 0 AGC Time Constant Selection
4 GAIN_MAN ON ON,OFF Manual Gain Control Enable
5 A_GAIN 0~1024 275 Manual Gain Value for Channel A
6 B_GAIN 0~1024 287 Manual Gain Value for Channel B
7 C_GAIN 0~1024 287 Manual Gain Value for Channel C
8 A_OFFSET 0~1024 0 Channel A Offset
9 B_OFFSET 0~1024 512 Channel B Offset
10 C_OFFSET 0~1024 512 Channel C Offset
11 YPM 0~7 4 Y Peaking Filter Mode
12 YSFM 0~32 1 Y Shaping Filter Mode
13 WYSFM 0~32 19 Wide Band TY Shaping Filter Mode
14 CSFM (0~7) 0 C Shaping Filter Mode
15 Contrast 0~255 128 Contrast Adjust
16 Brightness 0~255 126 Brightness Adjust
17 Hue 0~255 128 Hue Adjust
18 CKILLTHR 0~7 3 Colour Kill Threshold
19 SD_OFF_Cb 0~255 128 SD Offset Cb Channel
20 SD_OFF_Cr 0~255 128 SD Offset Cr Channel
21 SD_SAT_Cb 0~255 128 Saturation Cb Channel
22 SD_SAT_Cr 0~255 128 Saturation Cr Channel
23 IFFILTSEL 0~7 3 IF Filter Select
24 LTA 0~3 0 Luma Timing Adjust
25 CTA 0~7 3 Chroma Timing Adjust
26 DNR_TH 0~255 0 DNR Noise Threshold
27 DCT 0~3 0 Digital Clamp Timing
28 LAGC 0~7 0 Luma Automatic Gain Control
29 LAGT 0~3 3 Luma Automatic Gain Timing
30 LMG 0~4096 1064 Luma Manual Gain
31 CAGC 0~7(0~3) 2 Chroma Automatic Gain Control
32 CAGT 0~3 3 Chroma Automatic Gain Timing
33 CMG 0~4096 2458 Chroma Manual Gain
34 CTI_AB_EN ON ON,OFF Chroma Transient Improvement Alpha Blend Enable
35 CTI_AB 0~3 3 Chroma Transient Improvement Alpha Blend
36 CTI_C_TH 0~255 8 CTI Chroma Threshold
37 NSFSEL 0~3 0 Split Filter Selection NTSC
38 CTAPSN 0~3 2 Chroma Comb Taps NTSC
39 CCMN 0~7 0 Chroma Comb mode NTSC
40 YCMIN 0~7 0
41 HSSLICE 0~3 1
42 VSSLICE 0~3 3
43 DLL_PH
44 ST_NOISE OxFFFF
5. Upd64083
Akai DLP PT50DL14X TV Service mode
1 DYCOR 0 ~ 15 2 DY detection coring level
2 DYGAIN 0 ~ 15 9 DY detection gain
3 DCCOR 0 ~ 15 3 DC detection coring level
4 DCGAIN 0 ~ 15 6 DC detection gain
5 YHCOR 0 ~ 3 1 Y output high frequency component coring
6 CDELAY 0 ~ 3 4 C signal output delay
7 YPFT 3 YPFT adjustment
8 YPFG 8 YPFG adjustment
6. MSP4440
No Item Range Default Remark
1 MDB Effect 0~127 56 Micronas Dynamic Bass
2 SRS Dialog 0~127 64 SRS Dialog clarity adjustment
3 PLL Pilot low adjustment
4 PLH Pilot high adjustment
7. CCA(ON)
Akai DLP PT50DL14X TV Service mode
1 CCA On/Off On CCA On/Off Selection
2 Red-x 0~32768 640 Red-x adjustment
3 Red-y 0~32768 340 Red-y adjustment
4 Red-Y 0~32768 86 Red-Y adjustment
5 Green-x 0~32768 300 Green-x adjustment
6 Green-y 0~32768 620 Green-y adjustment
7 Green-Y 0~32768 300 Green-Y adjustment
8 Blue-x 0~32768 150 Blue-x adjustment
9 Blue-y 0~32768 60 Blue-y adjustment
10 Blue-Y 0~32768 53 Blue-Y adjustment
11 White-x 0~32768 291 White-x adjustment
12 White-y 0~32768 300 White-y adjustment
13 White-Y 0~32768 439 White-Y adjustment
14 WB Spread Spread CCA value to all mode
15 Move HDMI Move to the HDMI Mode
16 DRedX Target Red X value for CCA
17 DRedY Target Red Y value for CCA
18 DGreenX Target Green X value for CCA
19 DGreenY Target Green Y value for CCA
20 DBlueX Target Blue X value for CCA
21 DBlueY Target Blue Y value for CCA
22 DCyanX Target Cyan X value for CCA
23 DCyanY Target Cyan Y value for CCA
24 DMagentaX Target Magenta X value for CCA
25 DMagentaY Target Magenta Y value for CCA
26 DYellowX Target Yellow X value for CCA
27 DYellowY Target Yellow Y value for CCA
28 D_White_X Target White X value for CCA
29 D_White_Y Target White Y value for CCA
30 ATV/AV/SV
8. Cinema CCA
No Item Range Default Remark
1 DRedX 640 Target Red X value for CCA
2 DRedY 340 Target Red Y value for CCA
3 DGreenX 300 Target Green X value for CCA
4 DGreenY 620 Target Green Y value for CCA
5 DBlueX 150 Target Blue X value for CCA
6 DBlueY 60 Target Blue Y value for CCA
7 DCyanX 205 Target Cyan X value for CCA
8 DCyanY 270 Target Cyan Y value for CCA
9 DMagentaX 290 Target Magenta X value for CCA
10 DMagentaY 140 Target Magenta Y value for CCA
11 DYellowX 425 Target Yellow X value for CCA
12 DYellowY 515 Target Yellow Y value for CCA
13 D-White-X 313 Target White X value for CCA
14 D-White-Y 329 Target White Y value for CCA
9. SP Actuator
11. CHECKSUM 0000
Excute Checksum calcuation
No Item Range Default Remark
1 Actuator Gain 0~175 115 Actuator Gain adjustment
2 Actuator On/Off On Actuator On/Off selection
10. ESP
No Item Range Default Remark
1 Dynamic Con Off Dynamic Contrast On/Off
2 Dynamic Strength Medium Low/Mid/Mas
3 Dynamic Con Gain 0~100 0 Dynamic Contrast Gain Adjustment
4 Dynamic Sat Off Dynamic Saturation On/Off
5 Dynamic Sat Gain 0~255 176 Dynamic Saturation Gain Adjustment
6 Sharp Picture Off Sharp Picture On/Off
7 Sharp Filter HD Low HD High/HD Low/SD Image
8 Sharp Picture Gain 0~255 176 Sharp Picture Gain Adjustment
12. OPTION
No Item Range Default Remark
1 Lamp Clear Initialize lamp usage time. Lamp Life is set to zero
2 All setting is back to the default
3 WB Reset OFF Initialize the White Balance value
4 EER Reset Clear the EEPROM
5 Lamp Life 0h Lamp on time counter
6 AUTO POWER ON/OFF ON The sets turns on automatically when the power cord is
plugged in
7 DNle DEMO ON/OFF ON DNle Demo function selection
8 Lamp Control Dynamic Dynamic, Always
9 MUTE TIME 600ms Time which the screen will be black while switching
channels
10 EDID WRITE
11 DELAY MOD ON/OFF OFF Sound Delay Module ON/OFF selection
12 DBG/ANY SEL Debug/AnyNet Select the use of the Anynet jack
13 GEM/GEMIR SEL GemIR/Gemstar Not used
14 226 TEST PATT Xilleon 226 test pattern
15 Set Default Data Initialize Service Data
16 DDC protection OFF DDC write ON/OFF selection
17 LNA Default AUTO LNA setting OFF/Auto selection
18 PROTECT ON Protection ON/OFF selection
19 WATCH DOG Watch Dog ON/OFF selection
20 WD COUNT 0 Count for Watch Dog event
21 Auto Pgm Range 8 Not used
22 DIGITAL DMD Transfer engine adjustment data from digital to DMD
23 DMD DIGITAL Transfer engine adjustment data from DMD to digital
13. SERVICE
No Item Range Default Remark
1 V-Position 0 ~ 60 30 Screen upper and lower adjustment
2 H-Position 0 ~ 120 60 Screen left right adjustment
3 LAMP SYNC Pulse/Pass Pulse
4 Actuator Gain 105 Actuator Gain adjustment
5 INDEX DELAY 0 ~ 1023 166 Index delay adjustment
6 AUTO COLOR OFF Auto Color function execution
7 CCA CCA menu
8 Lamp Clear Initialize Lamp usage time
9 User Reset All setting is back to the default
10 Engine Select SAMSUNG SAMSUNG and ZEISS Selection
11 Lamp Watt 120W 120W/132W Selection
12 Lamp Select Philips Philips/Osram/Ushio
3-4 Service Adjustment
3-4-1 Vertical / Horizontal Position Adjustment
1. Turn off the power to put the unit into the STAND-BY mode.
2. In order to enter the Service Mode, Press "Mute" "1" "8" "2" "POWER" button on the Remote Control.
3. Select "Service" on the first display of the Service mode menu.
4. Select the V-position for vertical positioning and H-position for horizontal positioning by using the (up, down) buttons.
Do not set the V-position value to 34 or 35. (Setting to these values will cause horizontal lines on the right side of the screen.)
3-4-2 INDEX DELAY Adjustment
1. Turn off the power to put the unit into the STAND-BY mode.
2. In order to enter the Service Mode, Press "Mute" "1" "8" "2" "POWER" button on the Remote Control.
3. Select "Service" on the first display of the Service mode menu.
4. Press the channel (Up or Down) button to move to INDEX DELAY, then press ENTER to select.
5. The INDEX DELAY setup screen (with a red bar at the bottom of the screen) will be displayed.
6. Press the volume (Left of Right) button to check the red color at the bottom of the screen at its minimum and maximum values of
changing from red to magenta, then adjust to the mean value.
Alignment & Adjustment
3-14
3-4-3 CCAAdjustment Service Methods : CCAAdjustment is needed after changing a light engine or digital board
CCA : In DLP TV, even the same RGB color may differ depending on the light engine. CCA (Color Coordinate Adjustment)
corrects the color to achieve the color accuracy. CCA performs color correction after measuring and inputting the current
light engine's data on actual color coordinates for displayed Red, Green, Blue, and White color patterns, using a color
coordinate measuring equipment.
At this moment, color correction is performed on the basis of previously inputted Desired Color Coordinates and
Measured Color Coordinates. Measured Data on Service Engine's color coordinates is presented on the CCA label.
Input the label values to perform CCA color correction.
1. Condition of the CCA Label upon Receipt of the Service Engine
2. CCA Service Procedures
To execute CCA adjustment , perform the following steps :
1) Turn off the power to put the unit into the STAND-BY mode.
2) In order to enter the Service Mode, Press "Mute" "1" "8" "2" "POWER"
button on the Remote Control.
3) From the Factory Service Mode Menu; select SERVICE > CCA.
4) Switch the CCA OFF.
5) Enter the CCA Red, Green, Blue and White basic engine data to the DLP.
6) Input the D-White-x, y values in the coordinates per destination. (if necessary)
7) Select WB SPREAD, then press Enter to activate the WB Spread SET ensuring that
you adjust until you get the OK sign. After adjusting, exit Factory Mode.
8) When the adjustment is complete, check the picture quality.
Attention
Performing CCA is independent on current display's resolution and input signal type if you
don't measure color coordinates data.
Measuring color coordinates data requires specific equipment not possessed by service per
sonnel, that makes performing manual adjustment impossible. Adjusting CCA is applied to all the signal mode.
Don't change Desired value because it will be hamful to the color of the SET.
3-4-4 ACTUATOR GAIN Adjustment Akai DLP PT50DL14X TV
1. Before Adjustment
1) Turn off the power to put the unit into the STAND-BY mode.
2) In order to enter the Service Mode, Press "Mute" "1" "8" "2" "POWER" button on the Remote Control.
3) Select "Service" on the first display of the Service mode menu.
4) Press the (Up or Down) button to move to ACTUATOR GAIN, then press ENTER to select.
2. Making Adjustments
1) As shown in the picture above, change the actuator values to eliminate saw tooth shapes.
- To fine tune, increase the data value ensuring that you get the center between the starting and ending points of the
disappearing saw tooth shape.
Universal Remote - Service Mode - TV Factory menu codes
You are reading Akai DLP PT50DL14X TV Service Menu. Bookmark the Akai DLP PT50DL14X TV Service Menu page to your favorite.
https://tvservicemenu.blogspot.com/2015/02/akai-dlp-pt50dl14x-tv-service-menu.html.
Author : Meilyn, Ricky and Akzai Rajali
Editor : Denny Wowor
Akai DLP PT50DL14X TV Service Menu (All TV Service Menu Code)
5
stars -
"Akai DLP PT50DL14X TV Service Menu"
by Admin 2
Entering Akai DLP PT50DL14X TV Service mode, Akai DLP PT50DL14X TV Service Menu codes Written on February 19, 2015